SSD no longer detected, showing 0 MB or failed after a power outage? We recover data from SSDs – whether used privately or in a company, in the event of controller, firmware and electronics faults, manufacturer-independent and with TÜV-certified customer service.
An SSD (solid-state drive, also solid state disk) stores data with no moving parts – but compared with a classic hard drive with a rotating platter it has weak points of its own. The causes range from a controller fault through corrupted firmware to a power outage during a write operation. Typical symptoms: the SSD on the computer – whether a Windows PC, Mac or Linux system – suddenly shows 0 MB or is no longer detected at all. Even after a deletion the TRIM command matters: it permanently marks memory cells as free. It is crucial to take the SSD out of service immediately and not to write to it any further – then professional data recovery is still possible in many cases.
We work independently of the manufacturer on all common form factors, models and capacities.
Internal 2.5" SSDs with a SATA or SAS connector in notebooks, desktop PCs and servers – also as an external SSD via USB in an enclosure.
M.2 and PCIe SSDs with the NVMe protocol – high performance, but technically more demanding to recover in the event of a controller or firmware fault.
SSDs from servers and storage systems, also as part of a RAID array – often with a greater risk of data loss in the event of a failure.
SSD memory chips soldered directly onto the mainboard, e. g. in current Apple MacBooks, with no replaceable module.
Data recovery is carried out independently of the manufacturer – among others for manufacturers such as:
Whether mechanical, electronic or logical – the fault pattern determines the right procedure.
The controller manages communication between the host interface and the NAND flash memory chips. If the firmware is corrupted or the chip is faulty, the operating system can no longer address the SSD correctly – a repair is then only possible using specialised procedures.
Windows, macOS or Linux do not show the SSD at all, show it as "RAW" with no readable file system, or with 0 MB capacity – usually a sign of a controller or mapping error, not a total loss of the data. What to do when the SSD is not detected? →
A power outage during a write operation can cause the SSD mapping table to fail. The result: the drive hangs on startup, reports errors or is no longer visible in the BIOS.
After a deletion the TRIM command marks the affected memory cells as free and the SSD clears them permanently in the background. The faster you act, the higher the chance of recovering the deleted files.
After overvoltage, a lightning strike or a short circuit, often only the circuit board or the voltage regulator is affected, while the NAND flash memory chips with your data remain intact.
An SSD too can fail after water damage due to corrosion on the circuit board and components. Do not dry, blow-dry or switch it on – pack it safely and send it in.
Every memory cell tolerates only a limited number of write cycles (TBW). At the end of its service life the SSD sometimes switches to a read-only mode or reports read errors – then reading it out quickly counts.
With the right immediate measures you significantly increase the chance of a complete recovery:
Whether recovery is done logically or via the memory chips – in the end the file system has to be reconstructed. We work with all common formats on Windows, macOS and Linux, read out damaged partitions and recover data even after a format or from an SSD shown as "RAW".
Compared with a classic hard drive, an SSD stores its data distributed across NAND flash memory cells. The memory controller manages them via wear leveling and an internal mapping table – if this is lost, the raw data read out makes no meaningful sense at first. Reconstruction therefore requires the matching controller algorithm, special hardware and, in the case of physical faults, reading the memory chips directly.
Many SSDs are also hardware-encrypted (SED/OPAL) or secured with BitLocker or FileVault. Without the matching key, encryption remains a hurdle even after the cells have been read out successfully – so please have your recovery keys and passwords ready.
Each cell tolerates only a limited number of write cycles (TBW). At the end of its service life read errors accumulate – a sign to back up the data promptly. In complex cases our data forensics helps analyse damage and deleted structures.
The best protection against data loss is consistent data backup. The 3-2-1 rule has proven itself: three copies of your data, on two different storage media, one of them a backup copy kept offsite or in the cloud. That way your files are protected even in the event of a sudden SSD failure, after ransomware or an accidental data deletion.
Free initial assessment of your SSD damage by phone.
Shipping or pickup of the SSD – throughout Germany.
Technical diagnosis of controller, firmware and memory chips including a diagnostic report.
Binding fixed-price offer – your cost estimate before the recovery.
Data recovery – if necessary directly via the NAND flash memory chips.
Secure, encrypted handover of your recovered data.
With over 20 years of experience in data recovery, in our data recovery lab we first analyse the controller and the firmware of the SSD to distinguish a communication error from a physical chip fault. In serious cases we read the NAND flash memory chips directly and reconstruct the data using the controller algorithm and mapping table. An extensive stock of identical replacement controllers keeps recovery possible even for rare SSD models.
The final price depends on the damage and the effort involved – which is why we do not quote it as a flat rate, but only after the diagnosis, and then bindingly as a fixed price.
24/7 consultation